Multi Surface Oleophobic Treatment
Harmonization Code : 2901.10.00.00 | Acyclic hydrocarbons; Saturated
Main features
- General purpose hydrophobic/oleophobic treatment
- 30 - 300 nm thickness
- Reduces surface friction
Product Description
Aculon's Multi-Surface Oleophobic technology is designed to make many surfaces substrate hydrophobic, oleophobic, and repellent to nearly any liquid. Aculon's Multi-Surface Oleophobic treatment is quick and easy to apply, optically clear, and ultra-thin. For the application no capital investment is required, thus the treatment can be applied via several methods, including dip (30 nm), wipe (200-300 nm), or spray.
Advantages of Aculon's Multi-Surface Oleophobic Treatment
- Repels most liquids
- Optically clear (100% transmission)
- No capital equipment
- Easily reapplied in the field if damaged
Packaging
TDS, SDS & Technical Documents
- Aculon Multi-Surface Oleophobic Treatment SDS
Technical Specifications
General Properties
Thermal Properties
Electrical Properties
Other Properties
Additional Information
| Test Substrate | Water Contact Angle/Oil Contact Angle |
| Treated 304 Stainless Steel | 115 °/61 ° |
| Treated Glass Slide | 115 °/60° |
| Treated Aluminum | 117°/59° |
| Sliding Angle of Water Droplet (20 ?L distilled water) | >90° |
| % Haze of Reflected Light | 0% |
How to apply Aculon's Multi Surface Hydrophobic Treatment
|
STEP 1 ⇨ CLEAN |
STEP 2 ⇨ TREAT |
STEP 3 ⇨ DRY |
|
For this technology, cleaning is not typically required but is recommended. To clean, remove any visual dust, dirt, and grime that could damage the surface. |
Dip - Fully immerse the part in the treatment solution for 1 minute. Withdraw the part at a steady rate to ensure even coverage. Allow to dry or cure, then wipe clean with a microfiber cloth. |
Air dry at room temperature until the surface is dry to the touch. In some cases, additional thermal curing (e.g. 100°C for 5 minutes) may boost performance.
|
|
Wipe - Using a clean cotton cloth, wet it with the solution then rub the substrate for 10 seconds, air dry, then wipe clean with a microfiber cloth. |
||
|
Spray - Spray the solution on the substrate, air dry. If the coating is too thick, reduce the amount applied by changing the settings on the spray gun or using a diluent. |
Application Tips
- In some cases, additional thermal curing ( e.g. 100°C for 5 minutes) may boost performance.
- Inkjet printing or roll coating can also be used to apply the treatment.
- Spray Equipment Suggestions: HVLP(Binks Mach 1), HVLP(Devilbiss JGHV), Air Atomization(Devilbiss MBC gun), and Airless(Graco Model 225-292 President Pump Series A).
 |
Improved function of microfluidic devices |
| Impart repellency to paper, wood, fabrics, concrete, etc. | |
| Improve water repellency on eyewear | |
| Improve water repellency on electronic displays |
Recently viewed products
PTFE2S | 2-mil Skived PTFE Tape with Silicone Adhesive
- 2 mil Skived PTFE film
- Silicone adhesive
- >7500V breakdown voltage
DOWSIL™ TC-5550 Thermal Conductive Compound
- Good pump-out resistance for bare die application
- High thixotropy
- Low thermal resistance
PIT1S-UT-RL | 1mil Polyimide (Kapton) Tape | Ultra Thin Silicone Adhesive with Release Liner
- 1 mil polyimide film
- Ultra thin Silicone adhesive
- >6000V breakdown voltage
Humiseal Thinner 521EU
- RoHS Directive 2002/95/EC compliant
- For use with HumiSeal conformal coatings
- Ensures proper viscosity adjustment
WMC-G279 | White Epoxy Molding Compound
- White transmitting EMC for optocouplers
- Balanced moldability and cycle efficiency
- Low stress
HGPA12 | High Thermal Conductivity Gap Pad
- 0.14 Thermal Impedance
- 12 Thermal Conductivity
- Low oil bleeding & Low volatile
PIT0.5S-UT-DCD | 0.5 mil Die Cut Polyimide (Kapton) Tape with silicone adhesive| Single Sided Discs
- 0.5 mil polyimide film
- Ultra Thin Silicone Adhesive
- Die cut discs
BMI-3000 CG Low Cost Bismaleimide (Imide Extended) in Powder Form
- Superior thermal stability
- High adhesion to various substrates
- Hydrophobic toughener
